GN 2410 Telescopic linear slides with full extension, dual configuration


  • RoHS

Description

Specification

Rail / Runner
Heat treatable steel
  • zinc plated, blue passivated
  • Raceways hardened
Balls
Anti-friction bearing steel, hardened
Ball cage
Steel, zinc plated
Rail Connection
Screw Steel, zinc plated

Information

Telescopic linear slides GN 2410 consist of two linear motion ball slide rails connected at the runners. They are used, for example, in material handling or automation applications, or in jigmaking, to achieve a sliding motion in a linear direction when long extensions with low construction height of the rail are required.
The dual configuration has the advantage that both the radial and axial load capacities are identical. Meanwhile this design has proven less susceptible to dirt in practical use.
The rails and runner are equal in length. Both runners can be extended so that an extension is reached which is longer than the rail base length l1. Removing the support screws from the rails allows an extension of the rails on both sides.
External elements should limit the maximum sliding distance; the supports of the rail have been designed to guard against the inadvertent extraction of the runner from the rail.

On request

  • other lengths (based on the standard lengths grid dimension of 80 mm)
  • Special lengths (bore, start and end distances)

Technical information

Structure

All linear slides consist of an outer rail with a runner moving inside. Anti-friction bearings, kept at a distance and in position by means of a ball cage, lie between the rail and the runner. Rail and runner are made of heat treatable steel, enabling their use in industrial environments with higher requirements in terms of load rating, quiet operation and useful service life.
All designs are available in the nominal rail dimensions h1 = 28, 35 and 43 mm and may also be supplied beyond the standard range in lengths from 130 mm to 1970 mm, appropriate for individual requirements.
Linear slides are normally adjusted so that a clearance-free (i.e. moderately pre-stressed) match-up is created between rail and runner. The raceways of the rails and runners are induction hardened, which combined with the antifriction bearings results in lower wear and longer service life. Linear slides are permanently lubricated with a high-grade special grease designed for linear guide rail systems.
Depending on requirements, a variety of different types are available. Sliding distances of the runners are inside, partly outside or entirely outside the length of the rails. Fully extendable telescopic linear slides consist of linear slides directly interconnected at the rails, the runners or with the help of an intermediate profile.
To mount linear slides, countersinks in the rails and, depending on type of construction, threaded or countersunk holes in the runners are available. The compact style is generally advantageous for use in tight spaces.

Types

Telescopic linear slides, dual configuration, with full extension.

Assembly examples

Load rating of telescopic linear slides

in ascending order of the standard numbers
When selecting a suitable linear slide, it is primarily the available space, the desired stroke and the load carried which must be taken into consideration. The values listed below are intended as guidelines for selecting the most suitable nominal rail size.
The details on load rating are non-binding guide values given without liability and does not constitute any type of guarantee or warranty of its intended use. The user must determine in each individual case whether a product is suitable for the intended application. Environmental factors and aging may affect the stated values.

DescriptionLoad ratings
-Co rad in N
GN 2410-28-210444
GN 2410-28-370496
GN 2410-28-450405
GN 2410-28-530342
GN 2410-35-370534
GN 2410-35-450439
GN 2410-35-530403
GN 2410-35-610346
GN 2410-43-4501370
GN 2410-43-6101115
GN 2410-43-770870
GN 2410-43-930714
No details on the permissible load torques are given for the telescopic linear slides as these are normally used for paired applications. Loads of these dimensions occur to a minor degree because it may be assumed that the surrounding construction has sufficient rigidity and stiffness. Transferring load torques within certain limited is permitted.

Static load and deflection

The load values given in the tables refer to a maximum permissible force allowed to act in the middle of the fully extended profile rail at the third segment.
If the given values are observed and if the telescopic linear slide is fully extended, a minor deflection (sag) occurs at the end of the runner or of the rail. This has normally no detrimental effect on the proper function of the application. If required, guide values may be given if requested.

Mounting screws, assignment of the mounting holes

The standard mounting hardware is DIN 7991-10.9 countersunk head screws, to be mounted with the recommended tightening torque. Depending on type, not all mounting holes may be utilized. In general, these holes can be left unused. In exceptional cases, especially in bilateral stroke, mounting holes can be accessed by loosening the support screws and by pulling out the runner. The support screws are then put back in place.

Traversal speed, cage slip

The traversal speed in linear slides can be as much as 0.8 m/s. The particular application and the installation length can have an effect on this value. In the event of rapid changes of direction and high accelerating forces, cage slip may occur in some cases, especially in long ball cages. In cases such as these, the cage does not move synchronously with half the speed of the runner, but gradually loses its correct position owing to the slip. Whenever possible, running a blank stroke to the end of the traversal distance should be provided for back positioning.

Telescopic linear slides with full extension, dual configuration GN 2410
GN 2410
Filter
Description h1 l1 - l2 b1 b2 d s Weight
GN 2410-28-210 28 210 - 232 12.3 25.8 5.5 4 898
GN 2410-28-370 28 370 - 380 12.3 25.8 5.5 4 1630
GN 2410-28-450 28 450 - 464 12.3 25.8 5.5 4 1980
GN 2410-28-530 28 530 - 548 12.3 25.8 5.5 4 2300
GN 2410-35-370 35 370 - 406 16.5 34 6.5 3.5 2331
GN 2410-35-450 35 450 - 494 16.5 34 6.5 3.5 2835
GN 2410-35-530 35 530 - 558 16.5 34 6.5 3.5 3339
GN 2410-35-610 35 610 - 646 16.5 34 6.5 3.5 3843
GN 2410-43-450 43 450 - 486 21 44 8.5 4.5 4700
GN 2410-43-610 43 610 - 626 21 44 8.5 4.5 6400
GN 2410-43-770 43 770 - 796 21 44 8.5 4.5 8550
GN 2410-43-930 43 930 - 966 21 44 8.5 4.5 10000