DIN 808 Universal joints Steel / Stainless Steel, single or double


Description

Specification

Universal joints with friction bearing

Version in Steel

Types

  • Type EG: single, friction bearing
  • Type DG: double, friction bearing

Bore codes

  • Version B: without keyway
  • Version K: with keyway
  • Version V: with square
Steel
blank
Joint bearing areas / pins / bearing sleeves
case hardened

Version in Stainless Steel

Types

  • Type EG: single, friction bearing
  • Type DG: double, friction bearing

Bore code

  • Version B: without keyway
  • Version K: with keyway
  • Version V: with square
Stainless Steel AISI 304 NI

Universal joints with needle bearing

Types

  • Type EW: single, needle bearing
  • Type DW: double, needle bearing

Bore codes

  • Version B: without keyway
  • Version K: with keyway
  • Version V: with square
Steel
blank
Joint bearing areas, pins
case hardened

Information

The permissible r.p.m. of universal joints with friction bearing DIN 808 is to a large extent dependent on the type of application such as load, duration, angular disposition as well as lubrication . For over 1000 r.p.m. universal joints with needle bearing should be used
For continuous use ample lubrication is essential. This achieved by fitting the joint with a grease filled gaiter GN 808.1 

On request

  • with other or unequal bores

Technical information

  • Permissible r.p.m. and torque 

Mounting information

The single universal joints transfer the initial smooth rotation as an irregular rotation. One revolution of the drive shaft via single universal joint will cause the driven shaft to accelerate and decelerate twice. The extent of the irregularity depends on the operating angle ß.
In order to obtain a smooth rotation of the driven shaft two single or one double universal joint is required. In such cases where minor irregularities in the movement are acceptable or where minor operating angles are the norm a single universal joint will do.

For a smooth transfer of a rotating speed, the angle of inclination ß must be equal at both ends of the connecting shaft.

Due to a misconnection of the universal joint shafts, the irregular rotation of each joint is not compensated, but strengthened. This allows joint bearings and wedge profiles to be destroyed. For this reason, the markings of the universal joint shaft halves have to be opposite to each other.

Furthermore the bearings must be as close as possible to the universal joints.
For continuous operation of universal joints with friction bearings adequate lubrication is essential. If drip lubrication is not possible they should be lubricated at least once a day. It is also possible to fit the universal joint with a gaiter GN 808.1 which can be filled with oil or grease.

Selection of the size

Universal joints with friction bearing, Type EG

The table shows the transferable output N and/or torques M of universal joints DIN 808, type EG (single friction bearing) in relation 
The values are only applicable to a constant speed of rotation, constant load and an operating inclination angle of max. 10°. They are not applicable to universal joints in Stainless Steel.
For larger inclination angles ß a nominal output N increased by the correction coefficient k and/or a nominal torque M has to be selected (see example below).
Conversion formular:
Torque M [Nm] = 9550 N[kW]/n [min-1]
Output N [kW] = M [Nm] x n [min-1]
1 kW = 1.36 PS / 1 PS = 0.736 kW
Example 1
Output to be transferred N = 0.65 kW
R.p.m. n = 230 min-1
Angle of inclination ß = 10°
Correction coefficient k = 1
Indicative output N‘= Nominal output N
Intersection point P is arrived at from 0.65 kW and 230 min-1 (which corresponds to a torque of 27 Nm).
The next size up universal joint corresponding to point P is the model with a diameter d1 = 25.
Example 2
Torque to be transferred M = 27 Nm
R.p.m. n = 230 min-1
Angle of inclination ß = 30°
Correction coefficient k = 2.25
Indicative torque = 2.25 x 27 Nm = 60 Nm
Intersection point P1 is arrived at from 61 Nm and 230 min-1 (which is equivalent to an indicative output N = 1.47 kW).
The next size up universal joint corresponding to P1 is the model with a diameter d1 = 36.

Universal joints with needle bearing, Type EW

The table shows the transferable output N and/or torques M of universal joints DIN 808, type EG (single needle bearing) in relation 
The values are only applicable to a constant speed of rotation, constant load and an operating inclination angle of max. 10°.
For larger inclination angles ß a nominal output N increased by the correction coefficient k and/or a nominal torque M has to be selected (see example below).
Conversion formular:
Torque M [Nm] = 9550 N[kW]/n [min-1]
Output N [kW] = M [Nm] x n [min-1]
1 kW = 1.36 PS / 1 PS = 0.736 kW
Example 1
Torque to be transferred N = 5.5 kW
R.p.m. n = 2300 min-1
Angle of inclination ß = 10°
Correction coefficient k = 1
Indicative output N‘= Nominal output N
Intersection point P is arrived at from 5.5 kW and 2300 min-1 (which corresponds to a torque of 23 Nm).
The next size up universal joint corresponding to point P is the model with a diameter d1 = 28.
Example 2
Torque to be transferred M = 23 Nm
R.p.m. n = 2300 min-1
Angle of inclination ß = 18°
Correction coefficient k = 1.43
Indicative torque = 1.43 x 23 Nm = 33 Nm
Intersection point P1 is arrived at from 33 Nm and 2300 min-1 (which is equivalent to an indicative output N = 7.9 kW).
The next size up universal joint corresponding to P1 is the model with a diameter d1 = 32.

DIN 808 Steel, friction bearing
DIN 808
Filter
Description d1 d2 H7 l1 l2 l3 l4 t+1 max. assembly length
of the shaft
Weight
DIN 808-16-B6-34-EG 16 B 6 34 - 17 22 8 40
DIN 808-16-B6-56-DG 16 B 6 - 56 17 22 8 60
DIN 808-16-B8-40-EG 16 B 8 40 - 20 22 11 40
DIN 808-16-B8-62-DG 16 B 8 - 62 20 22 11 65
DIN 808-16-B10-52-EG 16 B 10 52 - 26 22 14 49
DIN 808-16-B10-74-DG 16 B 10 - 74 26 22 14 70
DIN 808-22-B10-48-EG 22 B 10 48 - 24 26 12 95
DIN 808-22-B10-74-DG 22 B 10 - 74 24 26 12 145
DIN 808-22-B12-62-EG 22 B 12 62 - 31 26 18 119
DIN 808-22-B12-88-DG 22 B 12 - 88 31 26 18 167
DIN 808-25-B12-56-EG 25 B 12 56 - 28 30 13 147
DIN 808-25-B12-86-DG 25 B 12 - 86 28 30 13 220
DIN 808-25-B16-74-EG 25 B 16 74 - 37 30 21 140
DIN 808-25-B16-105-DG 25 B 16 - 104 37 30 21 185
DIN 808-28-B14-60-EG 28 B 14 60 - 30 36 13 185
DIN 808-28-B14-96-DG 28 B 14 - 96 30 36 13 286
DIN 808-32-B16-68-EG 32 B 16 68 - 34 37 16 324
DIN 808
Filter
Description d1 d2 H7 s H10 l1 l2 l3 l4 t+1 max. assembly length
of the shaft
Weight
DIN 808-32-B16-105-DG 32 B 16 - - 105 34 37 16 430
DIN 808-32-B20-86-EG 32 B 20 - 86 - 43 38 24 382
DIN 808-32-B20-124-DG 32 B 20 - - 124 43 38 24 462
DIN 808-36-B18-74-EG 36 B 18 - 74 - 37 40 17 565
DIN 808-36-B18-114-DG 36 B 18 - - 114 37 40 17 599
DIN 808-42-B20-82-EG 42 B 20 - 82 - 41 46 18 700
DIN 808-42-B20-128-DG 42 B 20 - - 128 41 46 18 895
DIN 808-42-B25-108-EG 42 B 25 - 108 - 54 48 31 781
DIN 808-42-B25-156-DG 42 B 25 - - 156 54 48 31 1035
DIN 808-45-B22-95-EG 45 B 22 - 95 - 47.5 50 22 1137
DIN 808-45-B22-145-DG 45 B 22 - - 145 47.5 50 22 2220
DIN 808-50-B25-108-EG 50 B 25 - 108 - 54 55 26 1248
DIN 808-50-B25-163-DG 50 B 25 - - 163 54 55 26 1620
DIN 808-50-B30-132-EG 50 B 30 - 132 - 66 56 38 1660
DIN 808-50-B30-188-DG 50 B 30 - - 188 66 56 38 1764
DIN 808-58-B30-122-EG 58 B 30 - 122 - 61 68 29 1724
DIN 808-58-B30-190-DG 58 B 30 - - 190 61 68 29 2528
DIN 808-58-B32-130-EG 58 B 32 - 130 - 65 68 33 1724
DIN 808-58-B32-198-DG 58 B 32 - - 198 65 68 33 2619
DIN 808-70-B35-140-EG 70* B 35 - 140 - 70 72 35 2780
DIN 808-70-B35-212-DG 70* B 35 - - 212 70 72 35 3750
DIN 808-16-K6-34-EG 16 K 6 - 34 - 17 22 8 39
DIN 808-16-K6-56-DG 16 K 6 - - 56 17 22 8 62
DIN 808-16-K8-40-EG 16 K 8 - 40 - 20 22 11 40
DIN 808-16-K8-62-DG 16 K 8 - - 62 20 22 11 65
DIN 808-16-K10-52-EG 16 K 10 - 52 - 26 22 14 47
DIN 808-16-K10-74-DG 16 K 10 - - 74 26 22 14 69
DIN 808-22-K10-48-EG 22 K 10 - 48 - 24 26 12 96
DIN 808-22-K10-74-DG 22 K 10 - - 74 24 26 12 144
DIN 808-22-K12-62-EG 22 K 12 - 62 - 31 26 18 114
DIN 808-22-K12-88-DG 22 K 12 - - 88 31 26 18 157
DIN 808-25-K12-56-EG 25 K 12 - 56 - 28 30 13 163
DIN 808-25-K12-86-DG 25 K 12 - - 86 28 30 13 222
DIN 808-25-K16-74-EG 25 B 16 - 74 - 37 30 21 163
DIN 808-25-K16-105-DG 25 B 16 - - 104 37 30 21 222
DIN 808-28-K14-60-EG 28 B 14 - 60 - 30 36 13 185
DIN 808-28-K14-96-DG 28 K 14 - - 96 30 36 13 285
DIN 808-32-K16-68-EG 32 K 16 - 68 - 34 37 16 283
DIN 808-32-K16-105-DG 32 K 16 - - 105 34 37 16 426
DIN 808-32-K20-86-EG 32 K 20 - 86 - 43 38 24 317
DIN 808-32-K20-124-DG 32 K 20 - - 124 43 38 24 460
DIN 808-36-K18-74-EG 36 K 18 - 74 - 37 40 17 375
DIN 808-36-K18-114-DG 36 K 18 - - 114 37 40 17 565
DIN 808-42-K20-82-EG 42 K 20 - 82 - 41 46 18 595
DIN 808-42-K20-128-DG 42 K 20 - - 128 41 46 18 905
DIN 808-42-K25-108-EG 42 K 25 - 108 - 54 48 31 715
DIN 808-42-K25-156-DG 42 K 25 - - 156 54 48 31 1026
DIN 808-45-K22-95-EG 45 K 22 - 95 - 47.5 50 22 773
DIN 808-45-K22-145-DG 45 K 22 - - 145 47.5 50 22 1121
DIN 808-50-K25-108-EG 50 K 25 - 108 - 54 55 26 1098
DIN 808-50-K25-163-DG 50 K 25 - - 163 54 55 26 1606
DIN 808-50-K30-132-EG 50 K30 - 132 - 66 56 38 1241
DIN 808-50-K30-188-DG 50 K 30 - - 188 66 56 38 1557
DIN 808-58-K30-122-EG 58 K 30 - 122 - 61 68 29 1646
DIN 808-58-K30-190-DG 58 K 30 - - 190 61 68 29 2507
DIN 808-58-K32-130-EG 58 K 32 - 130 - 65 68 33 1703
DIN 808-58-K32-198-DG 58 K 32 - - 198 65 68 33 2598
DIN 808-70-K35-140-EG 70* K 35 - 140 - 70 72 35 2740
DIN 808-70-K35-212-DG 70* K 35 - - 212 70 72 35 3460
DIN 808-16-V6-34-EG 16 - V 6* 34 - 17 22 8 40
DIN 808-16-V6-56-DG 16 - V 6* - 56 17 22 8 64
DIN 808-16-V8-40-EG 16 - V 8* 40 - 20 22 11 56
DIN 808-16-V8-62-DG 16 - V 8* - 62 20 22 11 75
DIN 808-16-V8-52-EG 16 - V 8* 52 - 26 22 14 100
DIN 808-16-V8-74-DG 16 - V 8* - 74 26 22 14 142
DIN 808-22-V10-48-EG 22 - V 10* 48 - 24 26 12 123
DIN 808-22-V10-74-DG 22 - V 10* - 74 24 26 12 178
DIN 808-22-V10-62-EG 22 - V 10* 62 - 31 26 18 145
DIN 808-22-V10-88-DG 22 - V 10* - 88 31 26 18 215
DIN 808-25-V12-56-EG 25 - V 12* 56 - 28 30 13 189
DIN 808-25-V12-86-DG 25 - V 12* - 86 28 30 13 210
DIN 808-25-V12-74-EG 25 - V 12* 74 - 37 30 21 230
DIN 808-25-V12-105-DG 25 - V 12* - 104 37 30 21 275
DIN 808-28-V14-60-EG 28 - V 14* 60 - 30 36 13 348
DIN 808-28-V14-96-DG 28 - V 14* - 96 30 36 13 420
DIN 808-32-V16-68-EG 32 - V 16* 68 - 34 37 16 274
DIN 808-32-V16-105-DG 32 - V 16* - 105 34 37 16 420
DIN 808-32-V16-86-EG 32 - V 16* 86 - 43 38 24 274
DIN 808-32-V16-124-DG 32 - V 16* - 124 43 38 24 488
DIN 808-36-V18-74-EG 36 - V 18* 74 - 37 40 17 366
DIN 808-36-V18-114-DG 36 - V 18* - 114 37 40 17 536
DIN 808-42-V20-82-EG 42 - V 20* 82 - 41 46 18 580
DIN 808-42-V20-128-DG 42 - V 20* - 128 41 46 18 880
DIN 808-42-V20-108-EG 42 - V 20* 108 - 54 48 31 774
DIN 808-42-V20-156-DG 42 - V 20* - 156 54 48 31 1009
DIN 808-45-V22-95-EG 45 - V 22* 95 - 47.5 50 22 743
DIN 808-45-V22-145-DG 45 - V 22* - 145 47.5 50 22 1009
DIN 808-50-V25-108-EG 50 - V 25* 108 - 54 55 26 1025
DIN 808-50-V25-163-DG 50 - V 25* - 163 54 55 26 1565
DIN 808-50-V25-132-EG 50 - V 25* 132 - 66 56 38 1050
DIN 808-50-V25-188-DG 50 - V 25* - 188 66 56 38 1790
DIN 808-58-V30-122-EG 58 - V 30* 122 - 61 68 29 1565
DIN 808-58-V30-190-DG 58 - V 30* - 190 61 68 29 2420
DIN 808-58-V30-130-EG 58 - V 30* 130 - 65 68 33 1600
DIN 808-58-V30-198-DG 58 - V 30* - 198 65 68 33 2500
DIN 808-70-V35-140-EG 70* - V 35* 140 - 70 72 35 2650
DIN 808-70-V35-212-DG 70* - V 35* - 212 70 72 35 2800
DIN-808
Filter
Description d1 d2 H7 s H10 l1 l2 l3 l4 t+1 max. assembly length
of the shaft
Weight
DIN 808-22-B10-48-EW 22 B 10 - 48 - 17 26 12 95
DIN 808-22-B10-74-DW 22 B 10 - - 74 17 26 12 140
DIN 808-22-B12-62-EW 22 B 12 - 62 - 20 26 18 118
DIN 808-22-B12-88-DW 22 B 12 - - 88 20 26 18 170
DIN 808-25-B12-56-EW 25 B 12 - 56 - 24 30 13 145
DIN 808-25-B12-86-DW 25 B 12 - - 86 24 30 13 216
DIN 808-25-B16-74-EW 25 B 16 - 74 - 28 30 21 165
DIN 808-25-B16-105-DW 25 B 16 - - 104 28 30 21 183
DIN 808-28-B14-60-EW 28 B 14 - 60 - 34 36 13 183
DIN 808-28-B14-96-DW 28 B 14 - - 96 34 36 13 284
DIN 808-32-B16-68-EW 32 B 16 - 68 - 41 37 16 300
DIN 808-32-B16-105-DW 32 B 16 - - 105 41 37 16 320
DIN 808-32-B20-86-EW 32 B 20 - 86 - 54 38 24 320
DIN 808-32-B20-124-DW 32 B 20 - - 124 54 38 24 461
DIN 808-36-B18-74-EW 36 B 18 - 74 - 17 40 17 500
DIN 808-36-B18-114-DW 36 B 18 - - 114 17 40 17 554
DIN 808-42-B20-82-EW 42 B 20 - 82 - 20 46 18 450
DIN 808-42-B20-128-DW 42 B 20 - - 128 20 46 18 898
DIN 808-42-B25-108-EW 42 B 25 - 108 - 24 48 31 718
DIN 808-42-B25-156-DW 42 B 25 - - 156 24 48 31 1025
DIN 808-45-B22-95-EW 45 B 22 - 95 - 28 50 22 771
DIN 808-45-B22-145-DW 45 B 22 - - 145 28 50 22 1125
DIN 808-50-B25-108-EW 50 B 25 - 108 - 34 55 26 1095
DIN 808-50-B25-163-DW 50 B 25 - - 163 34 55 26 1594
DIN 808-50-B30-132-EW 50 B 30 - 132 - 41 56 38 1234
DIN 808-50-B30-188-DW 50 B 30 - - 188 41 56 38 1751
DIN 808-58-B30-122-EW 58 B 30 - 122 - 54 68 29 1653
DIN 808-58-B30-190-DW 58 B 30 - - 190 54 68 29 2496
DIN 808-58-B32-130-EW 58 B 32 - 130 - 17 68 33 1723
DIN 808-58-B32-198-DW 58 B 32 - - 198 17 68 33 2552
DIN 808-70-B35-140-EW 70* B 35 - 140 - 20 72 35 2600
DIN 808-70-B35-212-DW 70* B 35 - - 212 20 72 35 3200
DIN 808-22-K10-48-EW 22 K 10 - 48 - 24 26 12 95
DIN 808-22-K10-74-DW 22 K 10 - - 74 24 26 12 141
DIN 808-22-K12-62-EW 22 K 12 - 62 - 28 26 18 116
DIN 808-22-K12-88-DW 22 K 12 - - 88 28 26 18 163
DIN 808-25-K12-56-EW 25 K 12 - 56 - 34 30 13 142
DIN 808-25-K12-86-DW 25 K 12 - - 86 34 30 13 212
DIN 808-25-K16-74-EW 25 K 16 - 74 - 41 30 21 162
DIN 808-25-K16-105-DW 25 K 16 - - 104 41 30 21 180
DIN 808-28-K14-60-EW 28 K 14 - 60 - 54 36 13 180
DIN 808-28-K14-96-DW 28 K 14 - - 96 54 36 13 280
DIN 808-32-K16-68-EW 32 K 16 - 68 - 24 37 16 180
DIN 808-32-K16-105-DW 32 K 16 - - 105 24 37 16 417
DIN 808-32-K20-86-EW 32 K 20 - 86 - 31 38 24 313
DIN 808-32-K20-124-DW 32 K 20 - - 124 31 38 24 458
DIN 808-36-K18-74-EW 36 K 18 - 74 - 28 40 17 373
DIN 808-36-K18-114-DW 36 K 18 - - 114 28 40 17 558
DIN 808-42-K20-82-EW 42 K 20 - 82 - 37 46 18 595
DIN 808-42-K20-128-DW 42 K 20 - - 128 37 46 18 889
DIN 808-42-K25-108-EW 42 K 25 - 108 - 30 48 31 703
DIN 808-42-K25-156-DW 42 K 25 - - 156 30 48 31 1006
DIN 808-45-K22-95-EW 45 K 22 - 95 - 34 50 22 771
DIN 808-45-K22-145-DW 45 K 22 - - 145 34 50 22 1117
DIN 808-50-K25-108-EW 50 K 25 - 108 - 43 55 26 1085
DIN 808-50-K25-163-DW 50 K 25 - - 163 43 55 26 1590
DIN 808-50-K30-132-EW 50 K 30 - 132 - 37 56 38 1229
DIN 808-50-K30-188-DW 50 K 30 - - 188 37 56 38 1714
DIN 808-58-K30-122-EW 58 K 30 - 122 - 41 68 29 1631
DIN 808-58-K30-190-DW 58 K 30 - - 190 41 68 29 2531
DIN 808-58-K32-130-EW 58 K 32 - 130 - 54 68 33 1718
DIN 808-58-K32-198-DW 58 K 32 - - 198 54 68 33 2541
DIN 808-70-K35-140-EW 70* K 35 - 140 - 47.5 72 35 1920
DIN 808-70-K35-212-DW 70* K 35 - - 212 47.5 72 35 2760
DIN 808-22-V10-48-EW 22 - V10* 48 - 54 26 12 91
DIN 808-22-V10-74-DW 22 - V10* - 74 54 26 12 141
DIN 808-25-V12-56-EW 25 - V12* 56 - 61 30 13 91
DIN 808-25-V12-86-DW 25 - V12* - 86 61 30 13 208
DIN 808-28-V14-60-EW 28 - V14* 60 - 70 36 13 174
DIN 808-28-V14-96-DW 28 - V14* - 96 70 36 13 287
DIN 808-32-V16-68-EW 32 - V16* 68 - 24 37 16 174
DIN 808-32-V16-105-DW 32 - V16* - 104 24 37 16 414
DIN 808-36-V18-74-EW 36 - V18* 74 - 28 40 17 380
DIN 808-36-V18-114-DW 36 - V18* - 114 28 40 17 414
DIN 808-42-V20-82-EW 42 - V20* 82 - 37 46 18 572
DIN 808-42-V20-128-DW 42 - V20* - 128 37 46 18 620
DIN 808-45-V22-95-EW 45 - V22* 95 - 34 50 22 740
DIN 808-45-V22-145-DW 45 - V22* - 145 34 50 22 810
DIN 808-50-V25-108-EW 50 - V25* 108 - 43 55 26 1038
DIN 808-50-V25-163-DW 50 - V25* - 163 43 55 26 1518
DIN 808-58-V30-122-EW 58 - V30* 122 - 41 68 29 1560
DIN 808-58-V30-190-DW 58 - V30* - 190 41 68 29 2040
DIN 808-70-V35-140-EW 70** - V35* 140 - 47.5 72 35 2540
DIN 808-70-V35-212-DW 70** - V35* - 212 47.5 72 35 3000
DIN 808-NI
Filter
Description d1 d2 H7 s H10 l1 l2 l3 l4 t+1 max. assembly length
of the shaft
Weight
DIN 808-16-B6-34-EG-NI 16 B 6 - 34 - 54 22 8 40
DIN 808-16-B6-56-DG-NI 16 B 6 - - 56 54 22 8 60
DIN 808-16-B8-40-EG-NI 16 B 8 - 40 - 66 22 11 33
DIN 808-16-B8-62-DG-NI 16 B 8 - - 62 66 22 11 65
DIN 808-22-B10-48-EG-NI 22 B 10 - 48 - 61 26 12 100
DIN 808-22-B10-74-DG-NI 22 B 10 - - 74 61 26 12 150
DIN 808-25-B12-56-EG-NI 25 B 12 - 56 - 65 30 13 150
DIN 808-25-B12-86-DG-NI 25 B 12 - - 86 65 30 13 225
DIN 808-32-B16-68-EG-NI 32 B 16 - 68 - 70 36 16 290
DIN 808-32-B16-105-DG-NI 32 B 16 - - 105 70 36 16 144
DIN 808-42-B20-82-EG-NI 42 B 20 - 82 - 24 46 18 600
DIN 808-42-B20-128-DG-NI 42 B 20 - - 128 24 46 18 919
DIN 808-50-B25-108-EG-NI 50 B 25 - 108 - 31 55 26 1130
DIN 808-50-B25-163-DG-NI 50 B 25 - - 163 31 55 26 1620
DIN 808-16-K6-34-EG-NI 16 K 6 - 34 - 28 22 8 38
DIN 808-16-K6-56-DG-NI 16 K 6 - - 56 28 22 8 65
DIN 808-16-K8-40-EG-NI 16 K 8 - 40 - 37 22 11 40
DIN 808-16-K8-62-DG-NI 16 K 8 - - 62 37 22 11 65
DIN 808-22-K10-48-EG-NI 22 K 10 - 48 - 30 26 12 97
DIN 808-22-K10-74-DG-NI 22 K 10 - - 74 30 26 12 144
DIN 808-25-K12-56-EG-NI 25 K 12 - 56 - 34 30 13 146
DIN 808-25-K12-86-DG-NI 25 K 12 - - 86 34 30 13 219
DIN 808-32-K16-68-EG-NI 32 K 16 - 68 - 43 36 16 289
DIN 808-32-K16-105-DG-NI 32 K 16 - - 105 43 36 16 427
DIN 808-42-K20-82-EG-NI 42 K 20 - 82 - 37 46 18 598
DIN 808-42-K20-128-DG-NI 42 K 20 - - 128 37 46 18 900
DIN 808-50-K25-108-EG-NI 50 K 25 - 108 - 41 55 26 1098
DIN 808-50-K25-163-DG-NI 50 K 25 - - 163 41 55 26 1628
DIN 808-16-V6-34-EG-NI 16 - V6* 34 - 54 22 8 40
DIN 808-16-V6-56-DG-NI 16 - V6* - 56 54 22 8 60
DIN 808-16-V8-40-EG-NI 16 - V8* 40 - 47.5 22 11 40
DIN 808-16-V8-62-DG-NI 16 - V8* - 62 47.5 22 11 64
DIN 808-22-V10-48-EG-NI 22 - V10* 48 - 54 26 12 100
DIN 808-22-V10-74-DG-NI 22 - V10* - 74 54 26 12 145
DIN 808-25-V12-56-EG-NI 25 - V12* 56 - 66 30 13 1400
DIN 808-25-V12-86-DG-NI 25 - V12* - 86 66 30 13 219
DIN 808-32-V16-68-EG-NI 32 - V16* 68 - 61 36 16 230
DIN 808-32-V16-105-DG-NI 32 - V16* - 105 61 36 16 260
DIN 808-42-V20-82-EG-NI 42 - V20* 82 - 65 46 18 570
DIN 808-42-V20-128-DG-NI 42 - V20* - 128 65 46 18 886
DIN 808-50-V25-108-EG-NI 50 - V25* 108 - 70 55 26 1065
DIN 808-50-V25-163-DG-NI 50 - V25* - 163 70 55 26 1400