10.3 DIN 6885 Keyways

• Generals
  • 1. Plastic materials
    • 1.1 Mechanical strength
    • 1.2 Thermal resistance
    • 1.3 Strength and surface hardness
    • 1.4 Resistance to chemical agents
    • 1.5 Resistance to atmospheric agents and uv rays
    • 1.6 Flame resistance
    • 1.7 Electrical properties
    • 1.8 Surface finish and cleanability
    • 1.9 Compliance with international standards
    • 1.10 Competence of Elesa+Ganter technical department
  • 2. Metal materials
    • 2.1 Properties of metal inserts
    • 2.2 Clamping knobs with threaded inserts (types of assembly)
    • 2.3 Pass-through holes
    • 2.4 End of threaded studs
    • 2.5 Seizure risk with stainless steel threaded couplings
  • 3. Other materials
  • 4. Machining tolerances
  • 5. Fixed handles
  • 6. Assembly measures
  • 7. Special executions
  • 8. Colours
  • 9. Test values
  • 10. Technical tables
    • 10.1 Conversion tables
    • 10.2 DIN 79 Square holes and shafts
    • 10.3 DIN 6885 Keyways
    • 10.4 GN 110 and GN 110.1 Transversal holes
    • 10.5 DIN 13 ISO Metric threads
    • 10.6 DIN 228 Cylindrical GAS-BSP threads
    • 10.7 DIN EN ISO 898-1 | DIN EN 20898-2 Strenght values
    • 10.8 DIN ISO 286 ISO-Fundamental tolerances
    • 10.9 IP Protection Classification
    • 10.10.1 PFB | PRB Thread locking with jamming action Polyamide patch coating/ Polyamide complete coating
    • 10.10.2 MVK Thread locking gluing Micro encapsulation precote 80 (red)
    • 10.11 Stainless Steel characteristics
    • 10.12 Surface treatments
    • 10.13 Carbon steel, zinc alloys, aluminium, brass characteristics
    • 10.14.1 Duroplast, elastomer, technopolymer and rubber characteristics
    • 10.14.2 Duroplast, elastomer, technopolymer and rubber characteristics
    • 10.14.3 Duroplast, elastomer, technopolymer and rubber characteristics
    • 10.15 Load ratings U-Handles
    • 10.16 Load ratings metal hinges
    • 10.17 Strength of indexing plungers
    • 10.18 Assembly sets GN 965 and GN 968
  • 11. Vibration-damping elements
• Hygienic design
  • Design requirements for hygienic design
  • Seals
  • Design of the levelling feet gn 20
• Operating Elements
  • Executions with locking device
  • Safety handwheels
• Clamping knobs
  • Loss protection
• Control elements
  • Graduations
  • Scaling Sets
  • Bull's eye levels and screw-on levels
• Rotary controls
  • 1. Elesa-clayton position indicators
    • 1.1 Position indicators
    • 1.2 How to select the position indicators
    • 1.3 Special executions
  • 2. Gravity position indicators
    • 2.1 Ratios
    • 2.2 Choice of the indicator ratio
    • 2.3 Dials
    • 2.4 Accuracy
    • 2.5 Assembly instructions
  • 3. Positive drive indicators
    • 3.1 Ratios
    • 3.2 Choice of the indicator ratio
    • 3.3 Dials
    • 3.4 Assembly instructions
• Indexing elements
  • Load Capacity of Ball Lock Pins / Locking Pins
• Joints
  • Mounting information
  • Ball joint heads DIN ISO 12240-4 / DIN 12240-1, Series K
• Transmission elements
  • 1. Introduction to the transmissions
  • 2. Transmission elements
  • 2.1 The tooth
  • 2.2 Spur gears
  • 2.3 Racks
  • 3. Technical notes
  • 4. Applications
  • Glossary
• Levelling elements
  • Tables of the possible combinations bases / stems
  • No-slip disks for levelling elements
• Hinges
  • Guidelines for the correct application of plastic hinges
• Latches
  • Edge protection profiles
• Toggle, power and hook clamps
  • Toggle clamps
  • Pneumatic fastening clamps
• Accessories for hydraulic systems
  • Warnings for an effective protection of the reed switches
    • Inductive load
    • Capacitive load
    • Lamp load
    • Wiring capacitance
• Tube clamp connectors
  • Tube clamp connectors
  • Clamp mountings
  • Linear actuators
  • Longitudinal scales GN 299
  • Transfer unit and angular gears
  • Double tube linear actuators
• Castors and wheels
  • 1. General information
    • 1.1 Rubber wheels
    • 1.2 Polyurethane wheel
    • 1.3 Monolithic (hard tread) wheels
  • 2. Brackets
    • 2.1 Swivel bracket
    • 2.2 Fixed bracket
    • 2.3 Swivel bracket with brake
  • 3. Axle set
  • 4. Loads, friction and forces
    • 4.1 Sliding friction
    • 4.2 Rolling friction
    • 4.3 Tractive force
  • 5. Choosing the right wheel
    • 5.1 Nature and condition of the ground
    • 5.2 Environment
    • 5.3 Magnitude and nature of the load
    • 5.4 Speed and means of traction
    • 5.5 Manoeuvrability
    • 5.6 Choosing the wheel
  • 6. Glossary
• Magnets
  • Retaining magnets / Raw magnets
• Conveyor components
  • Modular roller tracks
    • Series
    • Technical data and guidelines for the choice
• Linear slides
  • Linear slides
  • Load rating of telescopic linear slides
  • Linear guide rail systems
  • Adjustable slide units
• Vibration mounts
  • High performance vibration dampers (AVC, AVM, AVF, AVG)
    • Features
    • Guidelines for the choice
• Vacuum components
  • Introduction to the vacuum
  • General features of the rubber compounds
• Elastomer springs
  • Resistance to chemical agents
  • Operating temperature