GN 23-X
GN 23
Leveling Feet
Stainless Steel, with Turned Base Plate, with Mounting Holes
External hex with internal thread
Stainless Steel, with Turned Base Plate, with Mounting Holes
External hex with internal thread

78711-R,20
78710-R,10
78712-R,50
orGN 300-30-B5-SW;60
GN 612-5-M12x1,5-A;40
DIN 172-B10,5-20-A;50
ISO 8675-M8x1-04-BT;10
Base plate
Stainless Steel AISI 304
Threaded stem
Stainless Steel AISI 303
Hexagon nut ISO 4032
Stainless Steel AISI 304
Rubber underlay, inlaid
NBR (Perbunan®), 70 Shore A
Leveling feet GN 23 will be delivered mounted and are not removable.
d1 | d2 | Static load in kN | - | - | - | - |
- | - | Versions of threaded stem | - | - | - | - |
- | - | S / SK | T / TK and U / UK | V / VK | W | X |
80 | M 8 | 6 | - | - | - | 17 |
80 | M 10 | 11 | - | - | - | 17 |
80 | M 12 | 16 | - | - | - | 17 |
80 | M 16 | - | 17 | 21 | 25 | 17 |
80 | M 20 | - | 28 | 35 | 35 | 28 |
80 | M 24 | - | 46 | 52 | 52 | - |
100 | M 8 | 6 | - | - | - | 17 |
100 | M 10 | 11 | - | - | - | 17 |
100 | M 12 | 16 | - | - | - | 17 |
100 | M 16 | - | 17 | 21 | 25 | 17 |
100 | M 20 | - | 28 | 35 | 35 | 28 |
100 | M 24 | - | 46 | 52 | 52 | - |
120 | M 20 | - | 28 | - | - | 28 |
120 | M 24 | - | 46 | - | - | - |
120 | M 30 | - | 43 | - | - | - |
At a spindle thread size M 10 and higher, the static load of the leveling feet GN 23 is limited owing to the permissible contact pressure of the adjustment spindle acting on the base plate (at a spindle strength ≥ 500 N/mm2). The values given in the table (valid for type D0 without rubber underlay) assume a clean pressure load perpendicular to the base plate. Bending and buckling stress which often occurs in practice results in a lower load-bearing capacity of the adjustment spindle and may have to be taken into account.
The details given on strength are non-binding guide values without any liability. In general, they do not constitute a warranty or quality.
The user must determine from case to case if a product is suitable for the intended purpose or use. Environmental factors may influence the stated values.
Versions of threaded stem | ||
![]() | ![]() | ![]() |
S / SK: External hex at the bottom at d2 M 8, M 10, M 12 | T / TK: Wrench flat at the bottom at d2 M 16, M 20, M 24, M 30 | U / UK: Hex socket at the top and wrench flat at the bottom at d2 M 16, M 20, M 24, M 30 |
![]() | ![]() | ![]() |
V / VK: External hex at the top and wrench flat at the bottom at d2 M 16, M 20, M 24 | W: Covered thread and wrench flat at the bottom at d2 M 16, M 20, M 24 | X: External hex with internal thread at d2 M 8, M 10, M 12, M 16, M 20 |
Your request was sent and will be answered as fast as possible.